Washer not draining: what to check, in order
Short answer: A washer that will not drain is usually blocked by lint, coins or small items in the drain pump filter, or by a kinked or badly placed drain hose. Clean the filter and check the hose first: both are free, take about 15 minutes, and solve most drain problems before you need a technician.
What causes a washer not to drain?
What causes a washer not to drain: the most common causes, how to check each one and who can fix it, from the most likely to the least likely.
| Cause | How to check | Cost or who fixes it |
|---|---|---|
| Clogged drain pump filter | Open the small panel at the bottom front and remove the filter | Free, about 15 minutes |
| Kinked or crushed drain hose | Pull the washer out and look behind it | Free |
| Hose pushed too far into the standpipe | Whirlpool: no more than 113 mm (4.5 in), with an air gap | Free |
| Drain placed too high | GE: about 8 ft (2.4 m) max for full size washers | Free to adjust |
| Clogged house drain | Run Spin with the hose in a bucket (LG test) | Plumber if the house drain is blocked |
| Faulty or jammed drain pump | Pump hums but no water moves | Repair technician |
Before you start
Unplug the washer and turn off the water taps. Put towels and a shallow tray on the floor: there may be several litres of water left in the drum, and it will come out of the filter opening. Keep the lowest part of the appliance in view while you work, so you can see where water comes from.
1. Clean the drain pump filter
On most front load washers, the drain pump filter sits behind a small panel at the bottom front of the machine. Whirlpool says this filter collects dirt, lint and other items and should be cleaned from time to time; on its all in one washer dryers it recommends doing it every 6 months.
- Open the small panel at the bottom front.
- If there is a thin hose next to the filter, pull it out, open its cap and let the water run into your tray.
- Turn the filter slowly counterclockwise and remove it.
- Remove lint, coins, hair ties and any small items, then rinse the filter and brush it with an old toothbrush.
- Screw the filter back in firmly so it does not leak, close the panel and run a Rinse and Spin cycle.
2. Check that the drain hose is not kinked
If the washer is pushed too close to the wall, the hose behind it can bend or get crushed. LG recommends leaving at least 10 cm (4 inches) between the back of the washer and the wall, and about 2 cm (1 inch) on each side.
3. Check how far the hose goes into the drain pipe
Whirlpool says the drain hose should not go more than 113 mm (4.5 inches) into the standpipe or laundry tub, and should not be taped in place. A small air gap is needed: without it, water can be siphoned back into the drum.
4. Check the drain height
The drain pump can only push water up to a certain height. GE gives about 8 feet (2.4 m) from the floor for most full size washers and 5 feet (1.5 m) for compact or portable washers. A drain placed higher than that will leave water in the drum.
5. Find out if the problem is the house drain
LG suggests a simple test: take the drain hose out of the drain pipe, put its end in a bucket and run a Spin cycle. If the water pumps out normally into the bucket, the washer is fine and the house drain pipe is probably clogged.
6. In winter, check for a frozen hose
If the washer is in a cold garage or basement, the drain hose or pump can freeze. LG advises pouring warm water into the drum and waiting 1 to 2 hours before trying again.
When to call a technician
If the filter is clean, the hose is straight and the house drain works, but the washer still will not drain, the drain pump itself may be faulty or jammed. At that point a repair technician is the safe choice, especially if you hear the pump humming without moving water.
Error codes that mean this problem
| Brand | Code | Meaning |
|---|---|---|
| Samsung washer | 5C | Not draining |
| LG washer | OE | Not draining |
| Bosch washer | E18 | Not draining |
| Whirlpool washer | F9 E1 | Long drain |
| GE washer | 18 | Combo unit pump filter clogged |
| GE washer | Po | Washer is slow to drain |
| Maytag washer | F9 E1 | Washer draining too slowly |
| Frigidaire washer | E2 | Water drains too slowly |
| Electrolux washer | E20 | Washer not draining |
Questions people ask
Why is my washer not draining or spinning?
Most washers will not spin until the water has drained, so a blocked drain pump filter or a kinked hose stops both. Clean the filter and straighten the hose first.
Can I run a cycle with water still in the drum?
It is better to drain it first through the filter opening or the small emergency hose. Running another cycle with a blocked drain usually ends with the same error.
How often should I clean the drain pump filter?
Whirlpool recommends every 6 months on some models, and sooner if you often wash pet bedding, towels or clothes with loose items in the pockets.
More guides
Sources: Whirlpool: Not Draining, Front Load Washer, Whirlpool: Not Draining, All In One Washer Dryer, LG: Water Not Draining (OE Error), GE Appliances: Front Load Washer Will Not Drain or Drains Slowly. Reviewed 2026-10-31. WhatsMyErrorCode is not affiliated with any manufacturer.