Bosch washer error code E18: not draining
Also shown as F18 on some Bosch models.
Bosch washer error code E18 means the washer couldn't pump the water out within the allowed time, so it stopped. In most cases the drain pump is blocked by lint, a coin or a hair clip, or the drain hose is kinked. Both can be fixed at home in about 30 minutes with towels and a flat container. Bosch's own advice is to clean the pump first, then check the hose.
Quick answer: start with drain the water and clean the pump. It takes 30 min and fixes the most common cause.
Signs you'll notice
- Water stays in the drum and the door won't open.
- The washer stops mid-cycle.
- E18 shows up mostly with large loads (impeller partly blocked).
What causes E18, most likely first
- Most commonBlocked drain pump or pump filter
Debris stops the pump impeller from turning freely.
- CommonKinked or blocked drain hose
Check the whole length from the washer to the standpipe.
- CommonBlocked house drain
The standpipe or sink trap is clogged.
- Less commonFailed drain pump motor
No sound at all during draining suggests the motor has died.
- RareFaulty pressure sensor
Can wrongly report that the drum hasn't emptied.
How to fix Bosch E18: free fixes first
Safety: unplug the washer before opening any panel.
1Drain the water and clean the pump
- Unplug the washer and let hot water cool down.
- Open the service flap at the bottom front (usually on the right).
- If there's a small emergency drain hose, use it to empty the water into a flat container. Otherwise unscrew the pump cover slowly; a lot of water will come out.
- Remove the pump cover and clean the inside, the thread and the housing so the impeller turns freely.
- Screw the cover back on firmly.
- Pour 1 litre of water into the detergent drawer and check that nothing leaks from the pump cover, then start the Drain or Spin programme.
Tip: Shine a torch into the pump housing and turn the impeller with a finger (washer unplugged). It should turn with slight resistance.
2Check the drain hose
- Pull the washer forward and look for bends in the drain hose.
- Disconnect it from the standpipe and check it isn't blocked.
- Run the Drain programme and check the hose connections stay watertight.
Still showing E18?
If the pump is clean, the impeller turns and the hose is clear, listen during draining. A hum without water moving means a broken impeller; total silence means a failed pump motor or a wiring fault. Both need a new pump, fitted by you or a technician.
Find the part for your modelMatch the part to the model number on the sticker inside the door or on the back.
How much does it cost to fix?
- Do it yourself
- $0
- Replacement part
- Drain pump: about $40 to $100
- Repair technician
- About $150 to $300 with labour
Indicative ranges, they vary by model and region.
Questions people ask about Bosch E18
Is E18 the same as F18 on a Bosch washer?
Yes, older Bosch models show F18 for the same drain fault.
How do I open my Bosch washer door after E18?
The door stays locked while there's water inside. Drain the water through the pump cover or emergency hose first.
How do I force a Bosch washer to drain?
Use the emergency drain hose next to the pump filter, or slowly unscrew the pump cover over a flat container.
Can E18 be caused by the house plumbing?
Yes. If the standpipe or sink drain is blocked, the washer can't push water out and shows E18.
Related washer codes
Samsung 5CWasher: Not drainingLG OEWasher: Not drainingWhirlpool F9 E1Washer: Long drainGE PoWasher: Washer is slow to drainGE 18Washer: Combo unit pump filter cloggedMaytag F9 E1Washer: Washer draining too slowlyFull guide: Washer won't drain · All Bosch washer codes
Sources: Bosch UK: E18 washing machine error. Reviewed 2026-10-07. WhatsMyErrorCode is not affiliated with Bosch.