F9 E1

Whirlpool washer error code F9 E1: long drain

Also shown as drn F21 F02 on some Whirlpool models.

Whirlpool washer error code F9 E1 means a long drain: the water level didn't drop in the expected time. Whirlpool lists three things to check first: how the drain hose is installed, the drain pump filter (on models that have one), and the small drain holes in the door seal. The most overlooked cause is a drain hose pushed too deep into the standpipe, which siphons water back into the washer. These checks are free and take about 20 minutes.

Quick answer: start with fix the drain hose installation. It takes 10 min and fixes the most common cause.

Signs you'll notice

What causes F9 E1, most likely first

Front of a front-load washer: the drain pump filter sits behind a small door at the bottom front corner, next to a thin emergency drain hose. Filter cap Emergency drain hose
Where to find the drain pump filter on most front loaders.

How to fix Whirlpool F9 E1: free fixes first

Safety: unplug the washer before opening any panel.

1Fix the drain hose installation

10 min, easy

  1. Unplug the washer and pull it away from the wall.
  2. Check how deep the hose goes into the standpipe. Pull it back so no more than 4.5 in (113 mm) is inside.
  3. Use the U-shaped hose form so the hose stays at the right depth.
  4. Remove any tape sealing the hose into the pipe: there must be an air gap.
  5. Check the hose for kinks or blockages along its length.
Did this fix it?

2Clean the drain pump filter

20 min, easy. You'll need: towels and a shallow tray

  1. On front loaders, open the access panel at the bottom front (on some models it's behind the lower dispenser drawer).
  2. Put towels and a shallow pan underneath: trapped water will flow out.
  3. Unscrew the filter slowly, remove debris and rinse it.
  4. Refit it firmly and close the panel.

Tip: Top loaders often have no user-accessible filter. If yours doesn't, skip to the hose and door-seal checks.

Did this fix it?

3Clear the door seal drain holes

5 min, easy

  1. Pull back the bottom of the rubber door seal.
  2. Clear lint from the small holes with a cloth or a cotton swab.
Did this fix it?

4Reset and test

5 min, easy

  1. Unplug the washer for 1 minute, then plug it back in.
  2. Run Drain & Spin and check the tub empties.
Did this fix it?

Still showing F9 E1?

If the hose is correctly installed, the filter and seal holes are clean, and the pump hums or buzzes without moving water, the pump has likely failed. Under warranty, Whirlpool replaces it.

Find the part for your model

Match the part to the model number on the sticker inside the door or on the back.

How much does it cost to fix?

Do it yourself
$0
Replacement part
Drain pump: about $30 to $80
Repair technician
About $130 to $250 with labour

Indicative ranges, they vary by model and region.

Questions people ask about Whirlpool F9 E1

What does F9 E1 mean on a Whirlpool washer?

Long drain: the washer didn't detect the water level dropping in the expected time.

How far should the drain hose go into the standpipe?

No more than 4.5 in (113 mm), according to Whirlpool. Deeper causes siphoning and this code.

Does every Whirlpool washer have a drain filter?

No. Many front loaders do; many top loaders don't have one you can reach.

Is F9 E1 caused by a bad drain pump?

Rarely. Check the hose installation, filter and door seal holes first.

Can I keep using my washer with F9 E1?

It's better not to: clothes stay wet and the pump works harder. Fix the drain first.

Related washer codes

Full guide: Washer won't drain · All Whirlpool washer codes

Sources: Whirlpool Product Help: F9 E1 front load washer. Reviewed 2026-10-07. WhatsMyErrorCode is not affiliated with Whirlpool.