Dishwasher not drying: what to check, in order
Short answer: Dishes usually stay wet because there is no rinse aid, because a quick or eco cycle skipped the heated dry, or because plastic and cupped items hold water. Refill the rinse aid, turn on heated dry and load items at an angle: these free fixes solve most drying problems before you suspect the heating element.
What causes a dishwasher not to dry dishes?
What causes a dishwasher not to dry dishes: the most common causes, how to check each one and who can fix it, from the most likely to the least likely.
| Cause | How to check | Cost or who fixes it |
|---|---|---|
| No rinse aid | Check the rinse aid indicator or dispenser | Free |
| Quick, 30 minute or Eco cycle | Use a normal cycle with Heated Dry | Free |
| Plastic and cupped items | Top rack, tilted; a few drops are normal | Free |
| Overloaded or nested items | Leave space so hot air reaches every surface | Free |
| Water not hot enough | At least 49 °C (120 °F) at the dishwasher (Whirlpool) | Free |
| Faulty heating element | Tub and dishes stay cold after a hot cycle | Repair technician |
1. Refill the rinse aid
Whirlpool calls a lack of rinse aid one of the most frequent reasons a dishwasher does not dry well. Rinse aid makes water slide off in a sheet instead of forming drops. Samsung goes further for its condensing dry models: without rinse aid, dishes will not get dry. If items are still wet with rinse aid, Whirlpool suggests raising the dose by one step; homes with hard water may need a higher setting.
2. Use a cycle with heated dry
Quick, 30 minute and Eco cycles may lower the heat and shorten drying, and Whirlpool notes they may not dry dishes completely. For a full load, especially with plastic, choose a normal or heavy cycle and turn on the Heated Dry or Extra Dry option.
3. Expect plastic to stay a bit wet
Plastic holds less heat than glass or china, so it dries more slowly. Whirlpool says it is normal for plastic and items with hollow surfaces to keep a few drops of water. Put plastic cups and bowls on the top or third rack, never on the bottom rack near the heater.
4. Load so water can run off
Dishes dry better when water can run off them. Tilt cups, bowls and glasses so water drains instead of pooling on the hollow side, and put them upside down on the top rack. Do not nest items together or overload the racks: hot air and steam need to reach every surface, and a crowded rack leaves wet spots where items touch.
5. Check the hot water temperature
Whirlpool says the hot water line should bring at least 49 °C (120 °F) to the dishwasher. Run the kitchen tap on hot until the water is hot before starting a cycle, so the dishwasher does not start with cold water.
6. Open the door at the end, or unload the bottom rack first
If you skip heated dry, KitchenAid recommends opening the door when the cycle ends to let steam out. Whirlpool notes this can take 6 to 8 hours for a full dry. Unload the bottom rack first so water from cupped items above does not drip on it.
7. Test the heating element
Whirlpool suggests running a cycle with Sanitize or a hot wash and Heated Dry, then carefully checking whether the dishes and the tub feel warm at the end. If they stay cold, the heating element or its control may be faulty: that is a repair for a technician. Some models also show a heater error code, listed below.
Error codes that mean this problem
| Brand | Code | Meaning |
|---|---|---|
| Bosch dishwasher | E09 | Heating fault in the pump heater |
| Samsung dishwasher | 3E | Incoming water too hot |
| Samsung dishwasher | HE | Temperature not detected correctly |
| LG dishwasher | HE | Water heating error |
| Bosch dishwasher | E12 | Limescale in the heat pump |
| Whirlpool dishwasher | F4E3 | Heating error |
| Whirlpool dishwasher | Sanitize light flashing | Sanitize temperature not reached |
| GE dishwasher | C6 | Incoming water too cold |
| Electrolux dishwasher | i60 | Water heating problem |
Questions people ask
Why are my plastic containers always wet after the dishwasher?
Plastic holds less heat than glass and china, so water does not evaporate as fast. A few drops are normal; rinse aid, heated dry and the top rack help.
Do I need rinse aid if my detergent already has it?
Manufacturers like Whirlpool and Samsung still recommend filling the rinse aid dispenser: it is one of the biggest factors for dry dishes, especially on models without a heated dry.
Is my dishwasher broken if the dishes are wet?
Usually not. Check rinse aid, the cycle and heated dry first. Suspect the heater only if the tub and dishes stay cold after a hot cycle with heated dry.
More guides
Sources: Whirlpool: Not Drying, Dishwasher, Whirlpool: Why is my dishwasher not drying dishes?, KitchenAid: Dishwasher not drying, 5 causes and fixes, Frigidaire: Dishwasher not drying, Bosch: Dishwasher is not drying, Samsung: Dishwasher does not dry dishes. Reviewed 2026-10-31. WhatsMyErrorCode is not affiliated with any manufacturer.