Dryer not heating: what to check, in order

Short answer: A dryer that runs but does not heat usually has a power or gas supply problem, a blocked vent, or a blown thermal fuse. Check the cycle setting, both circuit breakers (electric) or the gas valve (gas), then the vent. These free checks come first; a thermal fuse or heating element is a repair for a technician.

What causes a dryer not to heat?

What causes a dryer not to heat: the most common causes, how to check each one and who can fix it, from the most likely to the least likely.

CauseHow to checkCost or who fixes it
Air only or Eco cycle selectedChoose a normal heated cycleFree
One of two breakers tripped (electric)Reset both dryer breakers; needs 208 to 240 volts (GE)Free, electrician if it repeats
Gas valve closed or no gasValve handle parallel to the pipe means open (Whirlpool)Free, gas company if no supply
Blocked lint filter or ventClean the filter, check the hose and the outside flapFree
Blown thermal fuseDryer stopped heating after overheatingPart replacement, technician recommended
Faulty heating element, igniter or thermostatNeeds meter testingRepair technician

1. Check the cycle setting

Frigidaire and GE both remind that Air Fluff or Air Only cycles never heat. Samsung adds that Eco Dry lowers the heat on purpose to save energy. Choose a normal timed or sensor dry cycle with a regular heat setting before going further.

2. Electric dryer: reset both circuit breakers

An electric dryer uses two household circuits. Whirlpool explains that one can trip while the other stays on: the drum turns, but there is no heat. Turn both dryer breakers fully off, then on again, or replace both fuses (Whirlpool recommends time delay fuses). GE notes that a breaker can be partly tripped even when it looks normal, and that the dryer needs 208 to 240 volts to heat. If the problem continues, call an electrician.

3. Gas dryer: check the gas supply

Make sure the shutoff valve on the gas line behind the dryer is open: Whirlpool says the valve is open when its handle is parallel to the gas pipe. Frigidaire adds two checks: refill or replace the tank if you use propane (LP), and call your gas company if the natural gas supply was interrupted. If you smell gas, do not touch any switch: leave the home and call the gas company.

4. Clear the lint filter and the vent

Samsung explains that many dryers reduce or stop the heat when hot, moist air cannot leave, to protect against overheating. Clean the lint filter, then check the vent behind the dryer: it must not be kinked, flattened or crushed, and it must be open all the way to the outside flap.

  1. Unplug the dryer (and close the gas valve on a gas model).
  2. Pull the dryer forward and look at the vent hose behind it.
  3. Straighten any kink and replace a crushed foil or vinyl hose with a rigid or semi rigid metal duct.
  4. Go outside and check that the vent flap opens freely and is not blocked by lint or snow.
  5. Run a timed dry cycle and feel the air at the outside vent: it should be warm.

5. If it still does not heat: the thermal fuse

Dryers must have a thermal fuse that cuts the power when the inside gets too hot, often because of a blocked vent. It is a one time part: once it has opened, it must be replaced before the dryer is used again. Whirlpool recommends a professional for this, because the dryer has to be taken apart. Replace it only after fixing the vent, or the new fuse will blow again.

6. Other causes for a technician

If power, gas and airflow are fine, the heating element (electric), the igniter or gas valve coils (gas), or a thermostat may be faulty. These parts need testing with a meter and the dryer unplugged: book a qualified repair technician.

Error codes that mean this problem

BrandCodeMeaning
Samsung dryerHCDryer is overheating
Samsung dryerHC2Gas ignition error
LG dryernPNo power to heater
LG dryerGASNo gas supply detected
Bosch dryerE06Heating circuit fault
Whirlpool dryerF4 E1Heater or heater relay problem
Maytag dryerL2Low or no line voltage
Maytag dryerF4 E4Low line voltage diagnostic
Electrolux dryerE60Dryer not heating

Questions people ask

Why does my dryer run but not heat?

On an electric dryer, one of its two breakers is often tripped: the motor still runs, the heater does not. On a gas dryer, check that the gas valve is open. A blocked vent or a blown thermal fuse are the next most common causes.

Can a clogged vent stop the dryer from heating?

Yes. Many dryers lower or stop the heat when air cannot leave, and repeated overheating can blow the thermal fuse.

Is it safe to bypass a blown thermal fuse?

No. The thermal fuse is a fire safety part. Replace it with the correct part and fix the cause, usually a blocked vent.

More guides

Sources: Whirlpool: Dryer not heating, troubleshooting guide, Whirlpool: Not Heating, Gas Dryer, GE Appliances: Electric Dryer Runs But Does Not Heat, Frigidaire: My dryer is running but does not seem to be heating, Samsung: What to do when the dryer does not heat. Reviewed 2026-10-31. WhatsMyErrorCode is not affiliated with any manufacturer.