Dishwasher not draining: what to check, in order
Short answer: Standing water at the bottom of a dishwasher usually comes from a clogged filter, a blocked drain hose or a problem where the dishwasher connects to the sink or garbage disposal. Clean the filter first, then check the disposal and the hose: these free checks fix most drain problems.
What causes a dishwasher not to drain?
What causes a dishwasher not to drain: the most common causes, how to check each one and who can fix it, from the most likely to the least likely.
| Cause | How to check | Cost or who fixes it |
|---|---|---|
| Clogged filter or sump | Remove the lower rack and twist out the filter | Free, about 10 minutes |
| Knockout plug left in a new disposal | Look inside the disposal inlet after an installation | Free |
| Food stuck in the garbage disposal | Run the disposal | Free |
| Kinked drain hose or no high loop | Look under the sink | Free |
| Blocked air gap | Remove the chrome cap on the sink and clean it | Free |
| Jammed or faulty drain pump | Everything above is clear but water stays | Repair technician |
Before you start
Turn the dishwasher off and switch off its power at the breaker if you will reach into the bottom. Scoop or sponge out most of the standing water and keep a towel ready. Keep the lowest part of the appliance in view while you work, so you can see where water comes from.
1. Clean the filter and the sump
Whirlpool lists a clogged filter and debris in the sump among the most frequent causes, and Bosch's E24 code means the drain filter is blocked.
- Pull out the lower rack.
- Twist the filter counterclockwise and lift it out.
- Rinse it under warm water and scrub it with a soft brush.
- Look into the sump below for food, labels, seeds, toothpicks or broken glass, and remove them carefully.
- Put the filter back until it locks, then run a short rinse cycle to test.
2. Run the garbage disposal (and check the knockout plug)
Most built in dishwashers drain through the garbage disposal. Run the disposal to clear food stuck in it. If the dishwasher or the disposal was just installed, Whirlpool and Frigidaire both point to the knockout plug inside the disposal inlet: if it was never removed, the dishwasher cannot drain at all.
3. Check the drain hose
Look under the sink for a kinked, crushed or sagging drain hose. Whirlpool says the hose needs a high loop or an air gap: if it sits too low, dirty water can flow back into the tub and stay there.
4. Clear the air gap
If you have a small chrome cap on the sink deck, that is the air gap. Remove the cap and clean out any debris. Whirlpool notes that if water spills out of the air gap into the sink, the blockage is further down, between the air gap and the drain or in the sink plumbing.
5. Read the error code
Many dishwashers show a code for this problem: OE on LG, E24 on Bosch, i20 on Frigidaire, F9 E1 (long drain) on Whirlpool and Maytag. The code pages below explain what each one means for your brand.
When to call a technician
If the filter, disposal, hose and air gap are all clear but water still stays in the tub, the drain pump may be jammed or faulty. Whirlpool also recommends calling for service if you notice electrical problems, water leaks or a code you cannot clear.
Error codes that mean this problem
| Brand | Code | Meaning |
|---|---|---|
| Samsung dishwasher | 1E | Clogged filter (or overheating on some models) |
| Bosch dishwasher | E24 | Not draining, drain blocked |
| Bosch dishwasher | E25 | Drain pump blocked or cover loose |
| Bosch dishwasher | E22 | Filter blocked |
| Samsung dishwasher | 5C | Dishwasher will not drain |
| Samsung dishwasher | OC | Too much water inside |
| LG dishwasher | OE | Dishwasher not draining |
| Bosch dishwasher | E23 | Drain pump faulty or clogged |
| Whirlpool dishwasher | F9E1 | Long drain, not draining |
| GE dishwasher | C1 | Drain took too long |
| GE dishwasher | C3 | Dishwasher will not drain |
| GE dishwasher | F56 | Failure to drain |
| Maytag dishwasher | F9 E1 | Dishwasher not draining |
| Frigidaire dishwasher | i20 | Dishwasher did not drain |
| Frigidaire dishwasher | i40 | Clogged filter or sump |
| Electrolux dishwasher | i20 | Dishwasher not draining |
| Electrolux dishwasher | iF0 | Abnormal water level |
Questions people ask
Why is there still water in my dishwasher after a cycle?
A small amount of water in the sump is normal on many models. A puddle that covers the bottom usually means a clogged filter, a blocked hose or a garbage disposal problem.
My dishwasher stopped draining after a new garbage disposal. Why?
The knockout plug inside the disposal inlet was probably not removed. Whirlpool and Frigidaire both list it as the first check after an installation.
How often should I clean the dishwasher filter?
Check it every month or two, and sooner if you do not rinse plates or notice gritty dishes. A clean filter also helps the dishwasher wash better.
More guides
Sources: Whirlpool: Dishwasher Not Draining, Whirlpool: Newly Installed Dishwasher Not Draining, Frigidaire: What can I do if my dishwasher is not draining?, LG: How to fix an LG dishwasher that is not draining (OE), Bosch: Dishwasher error code E24. Reviewed 2026-10-31. WhatsMyErrorCode is not affiliated with any manufacturer.