Bosch dishwasher error code E24: not draining (causes, fixes and cost)
Also shown as E6103 on some Bosch models. Updated 13 November 2026.
Quick answer. Bosch E24 means the dishwasher did not drain within the expected time. The most common causes are a blocked filter, a loose pump cover, a kinked drain hose, or the garbage-disposal knockout plug still in place. Clean the filter and check the pump cover first — most cases clear in 15–30 minutes, with no parts.
If the tub is full of standing water, stop the cycle and read the safety note below before reaching into the dishwasher.
E24 vs E22: what is the difference?
| Code | What it usually means | First thing to check |
|---|---|---|
| E22 | The filter or micro-filter is blocked; water remains in the sump | Remove and clean the filter |
| E24 | The drain path is blocked; the dishwasher cannot drain | Filter, pump cover, drain hose, disposal plug |
| E25 | Drain pump blocked, pump cover loose, or check valve stuck | Pump impeller and cover |
The codes overlap: a clogged filter can produce E22 first and E24 if the cycle cannot finish. Bosch’s US support page for E24 points to the drain filter, drain hose, pump cover and garbage-disposal plug. Its E22 page points to the filter. (Bosch E24, Bosch E22)
Some Bosch displays use longer service codes for the same faults:
- E24 / E:24 / E-24 — same code.
- E6103 — Bosch lists it alongside E24 for the same drain fault on some models. (Bosch E24 or E6103)
- E22 / E9240 / E92-40 — same filter fault on some models. (Bosch E22 or E9240)
Symptoms you will notice
- Standing water at the bottom of the tub after a cycle.
- The cycle stops before the drain or dry phase.
- Dishes are wet and the detergent door may still be closed.
- Gurgling, humming or repeated drain attempts.
- E24 appears again after a reset.
- On a new installation, E24 appears on the first or second wash.
What causes E24, most likely first
- Most commonFilter or micro-filter blocked with food, grease or labels
Remove, rinse and re-seat the filter
- Very commonWhite drain-pump cover under the filter is loose or not clicked in
Press it down until it clicks; do not force it
- CommonDrain hose kinked, pinched behind the unit, or clogged
Pull the unit forward and inspect the hose
- CommonGarbage-disposal knockout plug still in place
Remove the plug from the disposal inlet
- Less commonSink siphon/air gap blocked or badly sealed
Clean the siphon; check the high loop
- Less commonCheck valve stuck closed
Replace the check valve
- RareDrain pump seized or failed
Replace the pump
Bosch’s official E24 checklist adds two things many guides miss: check the inlet hose for kinks and check that the siphon connection is sealed. Do those after the filter and pump cover, not before.
How to fix Bosch E24
- Switch off the dishwasher at the breaker.
- Unplug it if the plug is accessible.
- Do not reach into standing water near exposed wiring.
- If water has leaked under the unit, stop and call a technician.
1Clean the filter
- Remove the lower rack.
- Scoop out standing water with a sponge, cup or turkey baster.
- Twist the cylindrical filter counterclockwise and lift it out with the flat mesh screen.
- Rinse both parts under warm running water with mild dish soap and a soft brush.
- Check the sump under the filter for glass, labels, seeds or grease.
- Reinstall the filter and turn it until it locks.
Bosch’s filter-cleaning guide is the reference for the twist direction on your model. (Bosch filter cleaning)
2Check the pump cover
With the filter out, look for the white plastic cover over the drain-pump impeller.
- It should sit flat and click into place.
- If it is loose, press it down firmly with both thumbs.
- Do not pry it with a screwdriver; the plastic tabs break.
- If the cover is cracked or missing, replace it before running the dishwasher.
3Check the drain hose
- Pull the dishwasher forward enough to see the drain hose.
- Look for a sharp kink, a crush point, or a hose routed too high.
- Disconnect the hose at the sink or disposal and check for a blockage.
- Confirm the hose has a high loop or air gap, so dirty sink water cannot siphon back.
- Reconnect it securely and check for leaks.
4Check the garbage-disposal plug
If the dishwasher drains into a garbage disposal:
- Turn off the disposal at the wall switch.
- Remove the dishwasher hose from the disposal inlet.
- Shine a light into the inlet. A new disposal ships with a plastic knockout plug inside.
- If the plug is still there, knock it out with a screwdriver and remove all pieces.
- Reconnect the hose and clamp it.
This is one of the most common causes of E24 on a new installation.
5Reset and test
- Restore power.
- Press Start/Reset and hold it for about 3 seconds, or follow your model’s reset sequence.
- Run a short rinse cycle and watch the drain.
- If E24 returns immediately, go to “Still showing E24” below.
How to force a Bosch dishwasher to drain
“Force drain” does not override a physical blockage. It only starts a drain cycle.
- Press Start/Reset and hold until the display clears.
- Close the door and select Rinse or a short cycle.
- If the dishwasher hums but does not drain, stop it and check the filter and pump cover.
- If the tub is full, scoop the water out before removing the filter.
- Do not keep restarting the cycle — repeated attempts can overheat the pump.
If the pump runs but water does not move, the blockage is usually in the hose, check valve or disposal inlet.
Why does my Bosch dishwasher keep saying E24?
E24 that returns after a reset usually means one of these:
- The filter was rinsed but not locked back in.
- The pump cover was not clicked down.
- The drain hose is still kinked behind the unit.
- The disposal plug was only partially removed.
- The sink siphon is clogged.
- The check valve is stuck.
- The drain pump is weak or seized.
If you have checked all six and E24 returns, the next part is usually the check valve or drain pump, not the control board.
E24 with no visible blockage
This is the frustrating case: the filter looks clean, the hose looks clear, and E24 still returns.
Check these in order:
- Pump cover — it may look seated but one tab is not clicked. Press all four edges.
- Check valve — the rubber flapper at the pump outlet can stick closed or warp. It is a wear part, not a cleaning issue.
- Drain hose high loop — if the hose sags, water sits in it and the pump cannot prime.
- Disposal inlet — the knockout plug may be partially removed, leaving a plastic flap.
- Sink siphon — a clogged sink drain can back up into the dishwasher hose.
- Pump current draw — a technician can test whether the pump is running or seized.
Do not replace the control board until the pump has been tested. E24 is a drain fault, not a board fault, in most cases.
Compatible Bosch models
E22 and E24 are control-board codes, not model-specific codes. They appear across Bosch’s US dishwasher lines, including:
| Series | Representative US models | E24 / E22 |
|---|---|---|
| 300 Series | SHEM63W55N, SHSM63W55N | Yes |
| 500 Series | SHPM65Z55N, SHP95CM5N | Yes |
| 800 Series | SHP78CM5N, SHPM88Z75N | Yes |
| Benchmark | SHX89PW75N and other Benchmark models | Yes — confirm in the manual |
The exact sump and pump layout changes by series and year. Use the model/serial plate inside the door to order the right filter, pump cover or check valve. Do not order parts by the code alone.
How much does it cost to fix Bosch E24?
US estimates, 2026. Prices vary by market, model and whether the technician charges a trip fee.
| Repair | Parts | Installed / service |
|---|---|---|
| Clean filter and pump cover | $0 | $100–$150 service call |
| Drain hose | $10–$30 | $120–$220 |
| Check valve | $40–$90 | $185–$245 |
| Drain pump | $60–$160 | $285–$385 |
A repair company’s published range for Bosch drain repairs is $245–$385 all-in for check valve or pump work, with a $149 trip fee credited toward the repair. Filter-only calls are usually the trip fee. (Central Minnesota Appliance Repair)
DIY vs pro: if the filter and pump cover are the problem, DIY is $0 and 15 minutes. If the pump or check valve is the problem, pro repair is usually the better value because the dishwasher must be pulled out and the pump housing opened.
When to call a technician
Call a pro if:
- The pump runs but the tub does not drain after the filter and hose are clear.
- Water leaks from under the dishwasher.
- The pump cover is cracked or the sump is damaged.
- E24 returns after a check-valve cleaning.
- The dishwasher is under warranty — opening the pump housing may affect coverage.
- You are not comfortable working near water and mains power.
FAQ
How do I fix an E24 error on my Bosch dishwasher?
Clean the filter, check the white pump cover, inspect the drain hose and remove the garbage-disposal plug. Reset and run a short cycle. Most E24 faults are one of those four.
How do I force my Bosch dishwasher to drain?
Press and hold Start/Reset until the display clears, then run a Rinse cycle. If it hums without draining, stop and check the filter, pump cover and hose. Forcing the cycle will not clear a physical blockage.
Why does my dishwasher keep saying E24?
The filter may not be locked in, the pump cover may be loose, the drain hose may still be kinked, or the check valve may be stuck. If all four are clear, the pump is the next suspect.
What does the Bosch dishwasher error code E24 mean?
It means the dishwasher failed to drain within the expected time. Bosch’s US support page lists a blocked drain filter, a blocked drain hose, a loose pump cover and a new garbage-disposal plug as common causes.
Is E24 the same as E22?
No. E22 is usually a blocked filter or micro-filter. E24 is a drain-path fault. They overlap because a clogged filter can stop the drain and trigger either code.
Can I use the dishwasher with E24?
No. It will not finish the cycle and may leave standing water. Clear the blockage first.
Does E24 mean I need a new drain pump?
Usually not. Most cases are the filter, pump cover, hose or disposal plug. Replace the pump only after those are clear and the pump still does not run or move water.
How do I reset a Bosch dishwasher after E24?
Fix the blockage, restore power, then press and hold Start/Reset for about 3 seconds. Run a short rinse cycle to confirm the drain works.
Why does my new Bosch dishwasher show E24?
Check the garbage-disposal knockout plug and the drain-hose routing first. Both are common installation mistakes. Then check that the drain hose has a high loop.
Is E24 covered by warranty?
A manufacturing defect may be covered; a clog caused by food, grease or installation is usually not. Call Bosch support at 1-800-944-2904 or an authorized service provider before opening the pump housing.
Related codes
Sources: E24 error code, E22 error code, Cleaning the dishwasher filter, E24 or E6103, Bosch dishwasher not draining: E24/E25 costs, Bosch SHP78CM5N E22, Bosch E22/E24. Reviewed 13 November 2026. WhatsMyErrorCode is not affiliated with Bosch.