Bosch dishwasher error code E22: filter blocked (causes, fixes and cost)
Also shown as E9240 on some Bosch models. Updated 13 November 2026.
Quick answer. Bosch E22 means the dishwasher filter or micro-filter is blocked, so water cannot flow freely to the drain pump. Remove the lower rack, twist out the filter, rinse both parts under warm water, clear debris from the sump, and lock the filter back in. Most E22 faults clear in 15 minutes with no parts.
If the tub is full of standing water, switch off the breaker before reaching in.
E22 vs E24 vs E23
| Code | What it usually means | First check |
|---|---|---|
| E22 | Filter or micro-filter blocked; water remains in the sump | Remove and clean the filter |
| E23 | Drain pump blocked, clogged or faulty | Pump impeller and pump cover |
| E24 | Drain path blocked; the dishwasher cannot drain | Filter, pump cover, drain hose, disposal plug |
| E25 | Drain pump blocked, pump cover loose, or check valve stuck | Pump cover and check valve |
E22 and E24 overlap. A blocked filter can trigger E22 first and E24 if the cycle cannot finish. Bosch’s US pages treat E22 as a filter fault and E24 as a drain-path fault. (Bosch E22, Bosch E24)
Some Bosch displays use longer service codes:
- E22 / E9240 / E92-40 — same filter fault on some models. (Bosch E22 or E9240)
- E24 / E6103 — same drain fault on some models. (Bosch E24 or E6103)
Symptoms you will notice
- Water left in the bottom of the tub after a cycle.
- The cycle stops before draining.
- Dishes come out gritty, cloudy or still soapy.
- A greasy film or food debris on the filter.
- E22 returns after a rinse or reset.
- The dishwasher may hum or try to drain repeatedly.
What causes E22, most likely first
- Most commonFood debris, grease or labels blocking the cylindrical filter
Remove, rinse and brush the filter
- Very commonGrease film coating the fine mesh
Wash with warm water and mild dish soap
- CommonGlass, seeds, toothpicks or paper labels in the sump
Remove debris under the filter
- CommonFilter not locked back in after cleaning
Twist until it seats and locks
- Less commonFilter mesh torn or deformed
Replace the filter assembly
- Less commonDrain hose or pump cover restricting flow
Check the hose and pump cover
- RareDrain pump damaged by debris
Replace the pump
Bosch’s official E22 page is short: the filter is blocked, remove it, clean it under running water with mild soap and a soft brush, reinstall. The detail that matters is where the debris hides: in the cylindrical filter, under the flat mesh, and in the sump below it.
Where is the filter on a Bosch dishwasher?
It is at the bottom of the tub, under the lower rack and lower spray arm.
- Pull out the lower rack.
- Remove the lower spray arm if it blocks your hand.
- The filter is the cylindrical plastic tower with a flat mesh screen around its base.
- Twist the cylinder counterclockwise about a quarter-turn and lift it out.
- The flat mesh screen lifts out with it or separately, depending on the model.
If it will not turn, do not force it. Check your owner’s manual for that model’s release direction.
How to fix Bosch E22
- Switch off the dishwasher at the breaker.
- Unplug it if the plug is accessible.
- Scoop out standing water with a sponge or cup before removing the filter.
- Do not reach into the sump with wet hands while the unit is powered.
1Remove the filter
- Remove the lower rack.
- Twist the cylindrical filter counterclockwise.
- Lift out the cylinder and the flat mesh screen.
- Set them on a towel — do not bang them against the sink.
2Clean the filter
- Rinse both parts under warm running water.
- Use a soft brush and a drop of mild dish soap.
- Pay attention to the inside of the cylinder and the edges of the mesh.
- Do not use a wire brush, bleach or a dishwasher-cleaning tablet directly on the mesh.
- If the mesh is torn, replace the filter assembly instead of cleaning it.
3Clear the sump
With the filter out, look into the sump:
- Remove glass shards, seeds, labels, toothpicks and grease.
- Wipe the rubber seal and the filter seat.
- Check that the white pump cover is flat and clicked in.
- Do not pour water into the sump to “flush” it; that can overflow the base.
4Reinstall and lock the filter
- Seat the flat mesh screen first.
- Insert the cylinder and turn it clockwise until it stops and locks.
- Tug it gently — it should not lift out.
- Reinstall the spray arm and lower rack.
5Reset and test
- Restore power.
- Press and hold Start/Reset for about 3 seconds, or use your model’s reset sequence.
- Run a short Rinse cycle.
- Open the door at the end and check that the sump is empty.
If E22 returns immediately, go to the next section.
How to force a Bosch dishwasher to drain
E22 is usually a filter restriction, not a pump failure. “Forcing” a drain will not clear a blocked filter.
- Press and hold Start/Reset until the display clears.
- Select Rinse and close the door.
- If it hums but does not drain, stop it.
- Remove the filter and clear the sump.
- Check the drain hose and pump cover before trying again.
If the pump runs but water does not move after the filter is clean, treat it as E24/E25: check the hose, pump cover and check valve.
Why does E22 keep coming back?
- The filter is not locked all the way down.
- Grease film remains on the mesh even after a quick rinse.
- Food debris is trapped under the flat screen, not in the cylinder.
- The filter mesh is torn, so debris passes straight through.
- The drain hose is partially blocked, so the filter clogs again.
- Too much detergent or rinse aid is creating oversuds.
- The dishwasher is being loaded with large food scraps.
If E22 returns within a few cycles, replace the filter assembly before replacing the pump.
Compatible Bosch models
E22 is a control-board code, not a model-specific code. It appears across Bosch’s US dishwasher lines:
| Series | Representative US models | E22 |
|---|---|---|
| 300 Series | SHEM63W55N, SHSM63W55N | Yes |
| 500 Series | SHPM65Z55N, SHP95CM5N | Yes |
| 800 Series | SHP78CM5N, SHPM88Z75N | Yes |
| Benchmark | SHX89PW75N and other Benchmark models | Yes — confirm in the manual |
The filter assembly differs by series and model year. Use the model/serial plate inside the door to order the correct part; do not order by the code alone.
How much does it cost to fix Bosch E22?
US estimates, 2026. Prices vary by model, market and trip fee.
| Repair | Parts | Installed / service |
|---|---|---|
| Clean and re-seat the filter | $0 | $100–$150 service call |
| Filter assembly | $20–$60 | $120–$220 |
| Pump cover | $10–$30 | $120–$220 |
| Drain hose | $10–$30 | $120–$220 |
| Drain pump (if debris damaged it) | $60–$160 | $285–$385 |
| Check valve (if flow restriction persists) | $40–$90 | $185–$245 |
Most E22 cases are $0: the filter only needs cleaning. A filter assembly is usually $20–$60 and takes minutes to fit. Pro repair is worth it when the filter housing is damaged or E22 persists after cleaning.
When to call a technician
- The filter mesh is torn or the housing is cracked.
- E22 returns after a new filter is fitted.
- The pump runs but the sump does not empty.
- Water leaks from under the dishwasher.
- The dishwasher is under warranty.
- You are not comfortable removing the lower rack and filter.
FAQ
How do I fix error code E22 on my Bosch dishwasher?
Remove the lower rack, twist out the filter, rinse the cylinder and mesh with warm soapy water, clear the sump, lock the filter back in, then reset and run a rinse cycle.
How do I force my Bosch dishwasher to drain?
Press and hold Start/Reset until the display clears, then run a Rinse cycle. If it hums without draining, stop and clean the filter and sump. A forced cycle will not clear a physical blockage.
How do I reset a Bosch dishwasher after an error code?
Fix the underlying fault first. Then press and hold Start/Reset for about 3 seconds, or switch off the breaker for one minute and restart. Running a reset without cleaning the filter will usually bring E22 back.
What does E22 mean on a Bosch dishwasher?
The filter or micro-filter is blocked, so water remains in the sump. Bosch’s US support page describes E22 as a blocked filter and directs owners to remove and clean it.
Is E22 the same as E9240?
On some Bosch models, yes. E9240 and E92-40 are longer service-code versions of the same filter fault.
What is the difference between E22 and E24?
E22 is usually a blocked filter. E24 is a blocked drain path — filter, pump cover, drain hose or disposal plug. E22 can turn into E24 if the cycle cannot finish.
What does E-23 mean on a Bosch dishwasher?
E23 usually means the drain pump is blocked, clogged or faulty. Check the pump impeller and the white pump cover under the filter. If E23 follows E22, debris may have passed the filter and reached the pump.
Where is the filter on a Bosch dishwasher?
At the bottom of the tub, under the lower rack and lower spray arm. It is the cylindrical tower with a flat mesh screen around its base.
How often should I clean a Bosch dishwasher filter?
Bosch says regularly. Once a month is a practical baseline; clean more often if you scrape less, wash greasy pans, or see food debris on the filter.
Can I run my Bosch dishwasher with E22?
It may finish with dirty dishes or leave standing water. Clean the filter first; it takes about 15 minutes and costs nothing.
Is E22 covered by warranty?
A manufacturing defect may be covered; a clog caused by food, grease or a damaged filter is usually not. Call Bosch at 1-800-944-2904 or an authorized provider before replacing parts.
Related codes
Sources: E22 error code, E24 error code, Cleaning the dishwasher filter, E22 or E9240, E24 or E6103, Bosch SHP78CM5N E22, Bosch drain repair costs. Reviewed 13 November 2026. WhatsMyErrorCode is not affiliated with Bosch.