Bosch dishwasher error code E09: heating fault in the pump heater
Also shown as Error 09 E6001 on some Bosch models.
Bosch dishwasher error code E09 means there is a fault in the heating circuit. On most Bosch models, the water heater is built into the circulation pump, which Bosch calls the heat pump. Bosch US describes E09 as an internal heater fault in that pump, while Bosch UK simply calls it a defective heating element. Bosch's only home fix is a power reset at the breaker. If the code comes back, Bosch says to book a repair rather than try it yourself.
Quick answer: start with reset the power at the breaker. It takes 5 min and fixes the most common cause.
Signs you'll notice
- The dishwasher shows E09 or E:09 and stops the cycle.
- Dishes come out cold, wet or not fully clean.
- On some models the salt light is also on.
What causes E09, most likely first
- Most commonFailed heater in the circulation (heat) pump
The heater element inside the pump has burned out or lost its connection. The usual fix is replacing the pump.
- CommonLoose wiring or connector
A loose plug on the heater circuit can trigger the code. Only a technician should check this.
- CommonTemporary electronics glitch
A power surge can set the code. A power reset clears it if nothing is actually broken.
- Less commonDirty salt sensor (models with a salt light)
Bosch UK notes that if the salt light is on too, a dirty salt sensor may be part of the problem.
- RareControl board fault
The board that powers the heater can fail. This is diagnosed by a technician.
How to fix Bosch E09: free fixes first
Safety: unplug the dishwasher before opening any panel.
1Reset the power at the breaker
- Switch off the dishwasher's breaker for at least 30 seconds, as Bosch advises.
- Switch it back on and run a short cycle with no dishes.
- Open the door near the end of the cycle and check whether the tub feels warm.
2Check the salt sensor (if the salt light is on)
- Turn off the power at the breaker first.
- Open the salt container cap in the bottom of the tub and check it is clean and screwed on properly.
- Wipe away any grit or residue, then refit the cap.
Tip: This only applies to models with a water softener and a salt light. Many US Bosch models don't have one.
3Book a repair if the code returns
- Write down your model number (E-Nr) and serial number (FD) from the label on the door edge.
- Call Bosch customer support or a qualified appliance technician.
- Don't remove panels or test heater wiring yourself. The circuit runs on mains voltage.
Still showing E09?
If E09 returns after a power reset, the heater inside the circulation pump has most likely failed. On many Bosch models the heater and pump are one part, so the whole pump is replaced. Bosch advises against fixing this yourself, so call a technician.
Find the part for your modelMatch the part to the model number on the sticker inside the door or on the back.
How much does it cost to fix?
- Do it yourself
- $0
- Replacement part
- Circulation pump with heater: about $120 to $300
- Repair technician
- About $250 to $500 with labour
Indicative ranges, they vary by model and region.
Questions people ask about Bosch E09
What does E09 mean on a Bosch dishwasher?
There is a fault in the heating circuit. On most models the heater sits inside the circulation pump.
How do I reset a Bosch dishwasher E09?
Switch off the breaker for at least 30 seconds, then turn it back on. If E09 returns, Bosch says to call for service.
Can I use my Bosch dishwasher with E09?
It will usually stop, or wash without heating. Dishes won't be properly cleaned or dried until the heater is fixed.
Is E09 a heating element or a pump problem?
Both, in a way. Bosch dishwashers heat water inside the circulation pump, so the fix is often a new pump with built-in heater.
Can I replace the Bosch heat pump myself?
Bosch does not recommend it for safety reasons. The job involves mains wiring and taking the dishwasher out.
Why is my Bosch dishwasher not drying after E09?
Without heat, the final rinse stays cool and dishes don't dry well. The heating fault has to be repaired.
Related dishwasher codes
Samsung 3EDishwasher: Incoming water too hotSamsung HEDishwasher: Temperature not detected correctlyLG HEDishwasher: Water heating errorWhirlpool F4E3Dishwasher: Heating errorWhirlpool Sanitize light flashingDishwasher: Sanitize temperature not reachedGE C6Dishwasher: Incoming water too coldFull guide: Dishwasher not heating · All Bosch dishwasher codes
Sources: Bosch US: Dishwasher error codes, Bosch UK: Dishwasher E09 error. Reviewed 2026-10-10. WhatsMyErrorCode is not affiliated with Bosch.