Whirlpool dishwasher error code F6 E1: user interface error
Also shown as 6-1 flashing 6 pause 1 6 flashes, pause, 1 flash on some Whirlpool models.
Whirlpool dishwasher error code F6 E1 (often written F6E1) means a user interface error with the main control: the control panel and the main board aren't working together properly. On models without a display, the lights flash 6 times, pause, then once. It's often a temporary glitch, and Whirlpool's first step is simply to cut the power for 30 seconds and restart. Some repair sites describe F6E1 as a water fill problem, so if your dishwasher also isn't filling, check the water supply too.
Quick answer: start with do a full power reset. It takes 2 min and fixes the most common cause.
Signs you'll notice
- The dishwasher won't start a cycle, or stops responding partway.
- The lights flash in a 6, pause, 1 pattern.
- Buttons respond, but nothing starts.
What causes F6 E1, most likely first
- Most commonTemporary electronic glitch
Often after a power cut or surge. A power reset of at least 30 seconds clears it.
- CommonWater supply problem
Some guides link F6E1 to fill issues. Make sure the supply valve is open if the dishwasher isn't filling either.
- Less commonMoisture in the control area
Steam or water reaching the electronics in the door.
- Less commonFaulty control or user interface board
If the code returns after every reset.
How to fix Whirlpool F6 E1: free fixes first
Safety: unplug the dishwasher before opening any panel.
1Do a full power reset
- Unplug the dishwasher, or if it's hard-wired, turn off its breaker at the electrical panel.
- Wait at least 30 seconds (5 minutes is even safer) so the control fully resets.
- Restore power and start a short cycle.
2Check the water supply
- Make sure the valve under the sink is fully open.
- If the dishwasher didn't fill during the last cycle, check the supply hose for kinks.
3Let the door electronics dry
- If the code appeared after a leak, overflow or heavy steam, leave the power off and the door slightly open for a few hours.
- Restore power and test again.
Still showing F6 E1?
If F6 E1 comes back after a full reset with the water on, Whirlpool recommends calling for service. The usual repair is the main control board or the user interface board. A technician can confirm which one before you order a part.
Find the part for your modelMatch the part to the model number on the sticker inside the door or on the back.
How much does it cost to fix?
- Do it yourself
- $0
- Replacement part
- Control board: about $100 to $300
- Repair technician
- About $250 to $450 with labour
Indicative ranges, they vary by model and region.
Questions people ask about Whirlpool F6 E1
What does F6E1 mean on a Whirlpool dishwasher?
Whirlpool's help page lists it as a user interface error with the main control. Cut the power for 30 seconds; if the code stays, Whirlpool says to call for service.
What does 6 flashes then 1 flash mean?
That's F6E1 on models without a display: the lights flash 6 times, pause, then once.
Is F6E1 a water supply error?
Some repair sites say so. Whirlpool's help page lists it as a user interface / main control error, so reset first, then check the water if it isn't filling.
How do I reset a Whirlpool dishwasher with F6E1?
Unplug it or switch off its breaker for at least 30 seconds, then restore power.
Does Maytag use the same F6E1 code?
Yes. Maytag dishwashers are made by Whirlpool and use the same code and the same first step.
Related dishwasher codes
Samsung 3CDishwasher: Pump failureSamsung bEDishwasher: Stuck buttonLG LEDishwasher: Wash motor errorLG nEDishwasher: Spray arm motor errorLG PFDishwasher: Power failure detectedBosch E27Dishwasher: Low power supplyFull guide: Power, motor or control faults · All Whirlpool dishwasher codes
Sources: Whirlpool Product Help: 6 pause 1 (F6E1) dishwasher, Maytag Product Help: F6E1 dishwasher. Reviewed 2026-10-07. WhatsMyErrorCode is not affiliated with Whirlpool.