Whirlpool dishwasher error code F1 E1: control module fault
Also shown as E1 F1 1-1 flashing 1 flash, pause, 1 flash on some Whirlpool models.
Whirlpool dishwasher error code F1 E1 (also searched as E1 F1) points to the control module, the electronic board that runs the dishwasher. On models without a display, the lights flash once, pause, then once again. It can be a temporary glitch: Whirlpool's first step is to cut the power for 30 seconds. If the code comes back after that, the control usually needs service. There isn't much else to check yourself, and that's useful to know before spending money on parts.
Quick answer: start with reset the power. It takes 2 min and fixes the most common cause.
Signs you'll notice
- The dishwasher won't start, or stops right after starting.
- The lights flash once, pause, then once (1-1 pattern).
- The code appeared after a power cut, a storm or a surge.
What causes F1 E1, most likely first
- Most commonTemporary control glitch
Power cuts and surges can freeze the control. A reset clears it.
- CommonMoisture or steam damage
Steam reaching the board through the door over time.
- CommonFailed control module
If the code returns after each reset.
How to fix Whirlpool F1 E1: free fixes first
Safety: unplug the dishwasher before opening any panel.
1Reset the power
- Unplug the dishwasher, or turn off its breaker if it's hard-wired.
- Wait at least 30 seconds (5 minutes is even safer).
- Restore power and start a short cycle.
2Check the power supply
- Make sure the breaker isn't tripping and the outlet works with another appliance.
- If you had a storm or power cut, consider a surge protector or a check by an electrician.
Still showing F1 E1?
If F1 E1 returns after a full power reset, Whirlpool recommends scheduling service. The fix is usually a new control board. Have a technician confirm the diagnosis first: it's one of the most expensive dishwasher parts, so compare the quote with the price of a new dishwasher.
Find the part for your modelMatch the part to the model number on the sticker inside the door or on the back.
How much does it cost to fix?
- Do it yourself
- $0
- Replacement part
- Control board: about $100 to $300
- Repair technician
- About $250 to $450 with labour
Indicative ranges, they vary by model and region.
Questions people ask about Whirlpool F1 E1
What does F1 E1 mean on a Whirlpool dishwasher?
It points to the control module, the main electronic board. Try a power reset first.
Is E1 F1 the same as F1 E1?
Yes, it's the same code. Models without a display flash it as 1 flash, pause, 1 flash.
Can a reset fix F1 E1?
Sometimes. If it was a glitch from a power cut, a 30-second to 5-minute power reset clears it.
Is it worth repairing a Whirlpool dishwasher with F1 E1?
It depends on the dishwasher's age. A control board repair costs a few hundred dollars, so compare it with a new dishwasher if yours is old.
Related dishwasher codes
Samsung 3CDishwasher: Pump failureSamsung bEDishwasher: Stuck buttonLG LEDishwasher: Wash motor errorLG nEDishwasher: Spray arm motor errorLG PFDishwasher: Power failure detectedBosch E27Dishwasher: Low power supplyFull guide: Power, motor or control faults · All Whirlpool dishwasher codes
Sources: Whirlpool Product Help: 1 pause 1 (F1E1) dishwasher. Reviewed 2026-10-07. WhatsMyErrorCode is not affiliated with Whirlpool.