Whirlpool dishwasher error code F8 E4: water in drip tray
Also shown as E4 F8 8-4 flashing 8 flashes, pause, 4 flashes on some Whirlpool models.
Whirlpool dishwasher error code F8 E4 (often typed F8E4) means water has been detected in the drip tray under the tub. A small float switch rises when water collects there, and the dishwasher shuts down to prevent damage. Whirlpool's own help points first at a loose water supply connection, especially on newly installed dishwashers, and at too many suds. Some websites say F8E4 is a drain pump problem, but Whirlpool's help page treats it as a leak. Maytag and KitchenAid dishwashers use the same code.
Quick answer: start with turn off power and look for the leak. It takes 10 min and fixes the most common cause.
Signs you'll notice
- The dishwasher stops and beeps, or the lights flash 8 times, pause, then 4 times.
- Water or foam on the floor in front of or under the dishwasher.
- The code appears right after a new install, or after using regular dish soap.
What causes F8 E4, most likely first
- Most commonLoose or badly seated water supply connection
The fitting where the supply line meets the dishwasher valve, usually behind the bottom kick plate. Very common after a new install.
- Very commonToo many suds
Hand dish soap or too much detergent makes foam that pushes water out of the tub and into the base.
- CommonLeaking drain hose connection
Where the drain hose connects to the sink drain or garbage disposal.
- Less commonWorn door gasket or overloaded racks
Items sticking out can deflect water past the door seal.
- RareFaulty or disconnected float switch
The switch reports water that isn't there.
How to fix Whirlpool F8 E4: free fixes first
Safety: unplug the dishwasher before opening any panel.
1Turn off power and look for the leak
- Turn off the dishwasher at the breaker and close the water supply valve under the sink.
- Remove the kick plate at the bottom front (usually 2 screws).
- With a flashlight, look at the water supply fitting, the drain hose and the bottom of the tub.
- Wipe each connection with a dry paper towel: even a tiny damp spot shows where the leak is.
Tip: If your dishwasher was installed recently, start with the supply fitting. Whirlpool says the rubber washer must sit flat inside it, and the fitting should be hand-tightened, then about 1/4 to 1/2 turn more with pliers.
2Get rid of the suds
- Open the door. If you see foam, leave the dishwasher off and let the suds die down.
- Scoop out the remaining foam and water with a cup and towels.
- Only use dishwasher detergent, never hand dish soap, and use the recommended amount.
3Dry the drip tray
- With the kick plate off and power still off, soak up the water you can reach in the base pan.
- Leave the kick plate off and let the base dry. The float has to drop back down before the code clears, which can take several hours.
- Fix the leak you found before you run the dishwasher again.
4Reset and test
- Open the water valve, turn the breaker back on and run a short cycle.
- Watch the connections under the dishwasher for a few minutes with the kick plate still off.
Still showing F8 E4?
If the base is dry and nothing leaks but F8 E4 keeps coming back, the float switch may be stuck or badly connected. Whirlpool also notes the power cord must not touch the motor or the bottom of the tub. A technician can test the float switch.
Find the part for your modelMatch the part to the model number on the sticker inside the door or on the back.
How much does it cost to fix?
- Do it yourself
- $0
- Replacement part
- Float switch or supply fitting: about $10 to $40
- Repair technician
- About $120 to $250 with labour
Indicative ranges, they vary by model and region.
Questions people ask about Whirlpool F8 E4
What does F8 E4 mean on a Whirlpool dishwasher?
Water was detected in the drip tray under the tub. It's a leak or overflow warning, not usually a broken part.
Is F8E4 the same as E4 F8?
Yes. Some displays alternate the two parts of the code. Models without a display flash the lights 8 times, then 4 times.
Why does my new Whirlpool dishwasher show F8 E4?
On new installs the water supply fitting is the usual cause: the rubber washer isn't seated, or the fitting isn't tight enough.
Can dish soap cause F8 E4?
Yes. Hand dish soap makes heavy suds that push water out of the tub into the base, which trips the leak sensor.
How long does F8 E4 take to clear?
Once the leak is fixed, the base pan must dry so the float drops. That can take a few hours, or longer if a lot of water got in.
Is it a drain pump problem?
Not according to Whirlpool. Its help page treats F8E4 as a leak in the base, so check for water before buying a pump.
Related dishwasher codes
Samsung LCDishwasher: Leak detectedLG E1Dishwasher: Leak or overfill detectedBosch E15Dishwasher: Water detected in the baseGE LEAK DETECTEDDishwasher: Possible leak detectedMaytag F8 E4Dishwasher: Water in drip trayElectrolux i30Dishwasher: Leak protection activatedFull guide: Dishwasher leaking · All Whirlpool dishwasher codes
Sources: Whirlpool Product Help: F8E4 dishwasher. Reviewed 2026-10-07. WhatsMyErrorCode is not affiliated with Whirlpool.