Samsung dishwasher error code 4C: not getting enough water
Also shown as 4E flashing 4C on some Samsung models.
Samsung dishwasher error code 4C means the dishwasher isn't getting enough water: it opened the inlet valve, but the tub didn't fill in time. Older Samsung dishwashers show the same fault as 4E, and the code often flashes on the display. Most of the time the cause is under the sink: a supply valve that isn't fully open, a pinched hose, or a small mesh screen at the inlet valve clogged with limescale. A garbage disposal that was just installed is a classic culprit, because the hose gets squeezed behind it.
Quick answer: start with open the supply valve fully. It takes 2 min and fixes the most common cause.
Signs you'll notice
- The dishwasher hums at the start of the cycle but you hear no water coming in.
- 4C flashes within the first minutes of the cycle.
- It started right after work under the sink (new disposal, new faucet).
What causes 4C, most likely first
- Most commonSupply valve under the sink not fully open
Often the valve closest to the dishwasher, on the left under the sink.
- Very commonPinched or kinked supply hose
Frequently after a new garbage disposal or other plumbing work under the sink.
- CommonClogged inlet valve screen
A small mesh screen where the hose meets the valve. Hard water fills it with scale.
- Less commonLow household water pressure
Check if other taps in the kitchen run weakly too.
- Less commonFailed water inlet valve
Water reaches the valve but the valve doesn't open.
How to fix Samsung 4C: free fixes first
Safety: unplug the dishwasher before opening any panel.
1Open the supply valve fully
- Look under the sink for the valve on the dishwasher line.
- Turn it counter-clockwise until it stops.
2Check the hose under the sink
- Follow the supply hose from the valve towards the dishwasher.
- Look for sharp bends or spots where it's squeezed by the disposal, pipes or stored items.
- Free it and make sure it runs in a smooth curve.
3Clean the inlet valve screen
- Turn off the dishwasher at the breaker and close the supply valve.
- Remove the kick plate at the bottom front to reach the inlet valve.
- Disconnect the supply line from the valve, with a towel underneath.
- Pull out the small mesh screen inside the valve inlet, rinse it and brush off any scale.
- Refit the screen, reconnect the line firmly, open the water and check for drips before refitting the kick plate.
Tip: In hard-water areas, a white crust on the screen is the most common reason 4C comes back.
4Reset the dishwasher
- Switch the breaker off for 1 minute, then back on.
- Start a short cycle and listen for water filling in the first minute.
Still showing 4C?
If water reaches the valve (the screen and hose are clear) but the dishwasher still doesn't fill, the inlet valve is the likely failed part. If the valve gets no signal at all, a technician should check the door latch and the control board.
Find the part for your modelMatch the part to the model number on the sticker inside the door or on the back.
How much does it cost to fix?
- Do it yourself
- $0
- Replacement part
- Inlet valve: about $20 to $60
- Repair technician
- About $100 to $225 with labour
Indicative ranges, they vary by model and region.
Questions people ask about Samsung 4C
What does a flashing 4C mean on a Samsung dishwasher?
It's the same water supply error. The code flashes to get your attention; it doesn't mean a different fault.
Is 4C the same as 4E on a Samsung dishwasher?
Yes. Older Samsung dishwashers show 4E for the same water supply problem.
My Samsung dishwasher showed 4C after a new disposal was installed. Why?
The supply hose was probably pinched or kinked during the work. Check it under the sink first.
Is the Samsung dishwasher 4C code the same as on Samsung washers?
The meaning is similar (not enough water), but a dishwasher has a single supply line, so the checks are simpler.
Can I use my dishwasher with the 4C code?
No. It won't wash without water. Fix the supply, reset, and run a short cycle.
Related dishwasher codes
LG IEDishwasher: Not enough water fillingLG FEDishwasher: Too much water in tubBosch E14Dishwasher: Flow meter or fill problemBosch E16Dishwasher: Water filling problemBosch E18Dishwasher: Low water levelWhirlpool H20Dishwasher: Not detecting waterFull guide: Dishwasher not filling with water · All Samsung dishwasher codes
Sources: Samsung Canada: dishwasher error codes. Reviewed 2026-10-07. WhatsMyErrorCode is not affiliated with Samsung.