UE

LG washer error code UE: unbalanced load

Also shown as unbalanced error on some LG models.

An LG front load washer shows UE when it detects an unbalanced load. The laundry has bunched up on one side of the drum, and the drum's own movement cannot spread it out, so the washer stops before the spin. LG's help library gives the same first steps for every model: redistribute the clothes, fill the drum to about two-thirds, and make sure the washer is level. Most UE errors are fixed in a few minutes without any tools.

Quick answer: start with redistribute the laundry. It takes 5 min and fixes the most common cause.

Signs you'll notice

What causes UE, most likely first

How to fix LG UE: free fixes first

Safety: unplug the washer before opening any panel.

1Redistribute the laundry

5 min, easy

  1. Pause the cycle and wait for the drum to stop. Open the door.
  2. Pull out the clothes and untangle anything twisted into a ball.
  3. Spread the items evenly around the drum, with heavy and light pieces mixed.
  4. Close the door and restart the cycle, or run Drain and Spin.

Tip: Wet laundry is heavy. Take out items you can wring out by hand rather than lifting the whole mass.

Did this fix it?

2Adjust the load size

5 min, easy

  1. Fill the drum to about two-thirds of its capacity, which is what LG recommends.
  2. If you wash a single bulky item such as a rug, a pillow or a coat, add a few towels so the weight is shared.
  3. Wash very heavy items in smaller loads.
Did this fix it?

3Level the washer

10 min, medium. You'll need: a level, an adjustable wrench

  1. Put a level on top of the washer and check front to back and side to side.
  2. Turn the adjustable feet to raise or lower each corner until the bubble is centred.
  3. Tighten the lock nuts on the feet so they cannot turn.
  4. Push on each top corner. The washer should not rock.

Tip: A washer on a soft or uneven floor can pass a level check and still shake. Move it to a firm spot if you can.

Did this fix it?

4Run a test spin

10 min, easy

  1. Restart with an evenly spread load and watch the first spin.
  2. If UE returns with a balanced, two-thirds load and a level washer, stop using the washer and book a service visit.
Did this fix it?

Still showing UE?

If UE keeps returning with balanced loads on a level floor, the cause may be inside the suspension. Repair sites point to worn shock absorbers. LG does not document that on its help pages, so have a technician inspect the washer before you buy any part.

Find the part for your model

Match the part to the model number on the sticker inside the door or on the back.

How much does it cost to fix?

Do it yourself
$0
Replacement part
Varies by model. Check your model number before ordering.
Repair technician
Ask for a quote before the visit

Indicative only. Costs vary by model and region.

Questions people ask about LG UE

What does UE mean on an LG washer?

UE means unbalanced error. The washer detected that the load is uneven in the drum and stopped the spin.

How do I fix UE on an LG washer?

Redistribute the clothes so they are spread evenly, fill the drum to about two-thirds, and make sure the washer is level. Then restart the cycle.

Can a washer that is not level cause UE?

Yes. LG says UE can appear during the spin when the washer is not level, and that frequent UE may mean it needs to be levelled again.

Should I run the washer with only one item?

A single bulky item is hard to balance. Add a few towels so the weight is shared around the drum.

When should I call a technician?

If UE keeps coming back with a balanced load and a level washer, the suspension may be worn. Stop using the washer and have it checked.

Related washer codes

Full guide: Washer won't spin / unbalanced · All LG washer codes

Sources: LG Support: UE / UB error code, front load washer. Reviewed 2026-10-07. WhatsMyErrorCode is not affiliated with LG.