LG washer error code IE: water inlet error
Also shown as E02 E10 on some LG models.
LG washer error code IE means "inlet error": the washer didn't detect enough water coming in within the expected time. The causes are almost always simple: a tap that's partly closed, a kinked fill hose, low house pressure, or clogged mesh screens where the hoses connect. LG inlet valves need decent pressure (about 20 psi) to work. Start with the free checks below, which take about 15 minutes.
Quick answer: start with open the taps and check the hoses. It takes 5 min and fixes the most common cause.
Signs you'll notice
- The drum stays empty or fills very slowly.
- IE appears within seconds of starting a cycle (screens fully blocked).
- IE appears at busy times of day (low building pressure).
What causes IE, most likely first
- Most commonTap closed or only partly open
Check both hot and cold taps.
- Very commonClogged inlet screens
Small mesh filters in the inlet ports trap sediment over time.
- CommonKinked or pinched fill hose
Usually behind the washer, after it was moved.
- CommonLow household water pressure
The valve needs about 20 psi to open properly.
- Less commonFailed inlet valve or loose pressure hose
A loose pressure-sensor hose inside the washer can also report a false inlet error.
How to fix LG IE: free fixes first
Safety: unplug the washer before opening any panel.
1Open the taps and check the hoses
- Open both taps fully.
- Pull the washer out and straighten any bent or squashed hose.
2Clean the inlet screens
- Unplug the washer and turn off both taps.
- Unscrew the fill hoses from the back of the washer.
- Pull out the mesh screens in the inlet ports with needle-nose pliers.
- Rinse and scrub them, refit them, and reconnect the hoses hand-tight.
- Open the taps and check for leaks.
3Check your water pressure
- Open a nearby tap fully: a weak flow means low house pressure.
- Try a wash at a quieter time of day, or use a cheap pressure gauge on the tap.
Still showing IE?
If pressure is good and the screens are clean but the washer still won't fill, the water inlet valve has probably failed. A technician can test the valve and the pressure-sensor hose inside the cabinet.
Find the part for your modelMatch the part to the model number on the sticker inside the door or on the back.
How much does it cost to fix?
- Do it yourself
- $0
- Replacement part
- Inlet valve: about $20 to $60
- Repair technician
- About $120 to $250 with labour
Indicative ranges, they vary by model and region.
Questions people ask about LG IE
What does IE mean on an LG washer?
Inlet error: the washer didn't detect enough water entering in the expected time.
Can low water pressure cause IE?
Yes. LG inlet valves need about 20 psi. In buildings with weak pressure at peak hours, the washer can time out.
How do I clean LG washer inlet screens?
Turn off the taps, unscrew the hoses at the back, pull out the mesh screens with pliers, rinse them and put them back.
I replaced the inlet valve and still get IE. What now?
Check the house pressure and the pressure-sensor hose inside the washer. If both are fine, have the control board tested.
Related washer codes
Samsung 4CWasher: Not filling with waterSamsung OEWasher: Overflow / too much waterBosch E17Washer: Water takes too long to fillWhirlpool F8 E1Washer: Low water flowGE H2O SUPPLYWasher: Water is not entering washerMaytag F8 E1Washer: Slow or no water fillFull guide: Washer won't fill with water · All LG washer codes
Sources: PartSelect: fixing an LG washer IE code. Reviewed 2026-10-07. WhatsMyErrorCode is not affiliated with LG.