LG dryer error code d80: dryer exhaust vent about 80% blocked
Also shown as d75 d90 d95 on some LG models.
LG dryer error code d80 means the Flow Sense system has detected that the exhaust duct is about 80% restricted. LG uses the number as a rough blockage level: d75 is about 75%, d90 about 90% and d95 about 95%. The restriction is somewhere between the back of the dryer and the vent opening outside. With poor airflow the dryer can't keep its heater on for the whole cycle, so clothes take much longer to dry. LG warns that running a dryer with a severely restricted exhaust can be unsafe. On gas models, LG adds that d80 can also point to a lack of gas supply.
Quick answer: start with clean the lint filter and lighten the load. It takes 5 min and fixes the most common cause.
Signs you'll notice
- Clothes are still damp at the end of a normal cycle.
- The Flow Sense indicator shows bars, or the display shows d75, d80, d90 or d95.
- Weak or no airflow at the vent flap outside the house.
What causes d80, most likely first
- Most commonLint build-up in the vent duct
Lint collects inside the duct and wall vent over time. LG recommends a professional vent cleaning every year.
- Very commonCrushed or kinked duct behind the dryer
Pushing the dryer back flattens the duct. A duct coiled like a spring or with loose joints also restricts airflow.
- CommonOutside vent flap stuck or clogged
The exhaust flaps must open fully. Lint, a nest or ice can hold them shut.
- CommonVent run too long or too many elbows
LG limits 4-inch rigid metal duct to 65 ft with no elbows, less with each bend, and no more than four 90° elbows.
- Less commonNo gas supply (gas models only)
LG notes that on gas dryers d80 may mean gas isn't reaching the dryer, for example a closed supply valve.
How to fix LG d80: free fixes first
Safety: unplug the dryer before opening any panel.
1Clean the lint filter and lighten the load
- Remove the lint from the filter before every load.
- If it looks clogged even when empty, wash it with warm water and a soft brush, then let it dry.
- Dry smaller loads until the airflow problem is fixed.
2Check the outside vent flap
- Start an Air Dry (no heat) cycle on the dryer.
- Go outside and check that the vent flaps open fully and air blows out strongly.
- Remove any lint, nests or debris around the vent opening.
3Straighten or replace the duct behind the dryer
- Unplug the dryer before you move it. On a gas dryer, don't pull or bend the gas line.
- Pull the dryer out carefully and look for crushed, dented, kinked or torn duct.
- Make the duct run straight or in a gentle S curve, never coiled.
- Replace plastic, vinyl or thin foil duct with 4-inch rigid or semi-rigid metal duct.
- Seal the joints and push the dryer back without crushing the duct.
Tip: If you smell gas at any point, don't touch any switches. Leave the house and call your gas company.
4Clean the full vent run
- Disconnect the duct from the back of the dryer.
- Push the vent brush through the duct toward the outside, pulling out lint as you go.
- Reconnect the duct and run the dryer to see if the code comes back.
Tip: Vents inside walls or through the roof are best left to a professional dryer vent cleaner.
5Check the vent length and the gas supply
- Ask your vent cleaner for the total duct length and the number of 90° elbows.
- Compare with LG's limits: for 4-inch rigid metal duct, 65 ft straight, 55 ft with one elbow, 28 ft with four.
- On a gas dryer, make sure the gas shut-off valve is open. Don't disconnect or move the gas line yourself.
Tip: If the run is too long, a shorter route or fewer elbows is the only lasting fix.
Still showing d80?
d75 to d95 are airflow warnings, not a failed part, so fix the venting before replacing anything. LG doesn't publish a button sequence to clear the code: once airflow is restored, run the dryer and check that the code stays off. If the venting is clean, short and within LG's limits and the code returns, book an LG service visit.
Find the part for your modelMatch the part to the model number on the sticker inside the door or on the back.
How much does it cost to fix?
- Do it yourself
- $0
- Replacement part
- Vent brush kit or 4-inch metal duct: about $15 to $40
- Repair technician
- About $100 to $200 for a professional vent cleaning
Indicative ranges, they vary by model and region.
Questions people ask about LG d80
Can I still use my LG dryer with d80?
It's better not to. The heater can't stay on for the whole cycle, so drying is slow. LG warns that a severely restricted exhaust can be unsafe.
How do I clear d80 on an LG dryer?
Fix the airflow: clean the lint filter, straighten the duct and clear the outside vent. Then run the dryer and check whether the code comes back.
What is the difference between d80 and d90?
They show how blocked the exhaust is. LG says d80 is about 80% restricted, d90 about 90% and d95 about 95%.
Why does my LG dryer show d80 after the vent was cleaned?
The restriction may be elsewhere: a crushed duct behind the dryer, a stuck outside flap, or a run that is too long. On gas models, also check the gas supply.
How long can an LG dryer vent be?
LG allows up to 65 ft of 4-inch rigid metal duct with no elbows. Each 90° elbow lowers that limit, and four elbows is the maximum.
What do the bars on the LG Flow Sense indicator mean?
They show how restricted the exhaust is. LG says two or four bars mean the exhaust system is severely restricted.
Related dryer codes
Samsung ClgDryer: Vent is cloggedSamsung C90Dryer: Vent mostly blockedBosch E01Dryer: Lint filter is blockedBosch E12Dryer: OverheatingWhirlpool AFDryer: Restricted airflowGE Check VentDryer: Dryer vent is blockedFull guide: Dryer vent blocked · All LG dryer codes
Sources: LG US: LG Dryer: Error Code List, LG US: Understanding d90 and d95 Error Codes, LG US: Error Codes: Laundry Dryer, LG US: Proper Venting and Installation Tips, LG US: Installation Check: Laundry Dryer. Reviewed 2026-10-10. WhatsMyErrorCode is not affiliated with LG.